Top Smart 18"


Our newest lace front topper blends our signature SmartLace™ design with the lightweight comfort of a crown topper. Top Smart has a 9-inch base with 6 strategically placed clips that distribute weight evenly for maximum comfort. Designed for the advanced stage of hair loss, this lace front topper also features 3 polyurethane tabs to facilitate the use of adhesive if desired. Available in 12″ and 18″ lengths this hair topper is recommended for the beginning stage of hair loss. The heat-resistant fiber allows the wearer to heat style the piece for the most flexibility. easiPart HD is available in various lengths: 8″, 12″ and 18″

Item Number: 6001
Color Shown: 6
Hair Type: Synthetic
Base Dimension: 9″ x 9
Collection: Toppers
Application Method: Tape/Clip
Length: 18″
Weight: 4.3 oz
Base Design: Single Monofilament / Wefted

027 367 7686




•  Before washing, gently remove any tangles using your Jon Renau Wide Tooth Comb ONLY
•  Wet hair completely using cool running water
•  Gently lather the hair with a small amount of Jon Renau Synthetic Shampoo, making sure that the hair is traveling in the same direction. DO NOT rub hair; this will cause tangling
•  Rinse thoroughly under cool running water until water runs clear
•  Wrap wig or hairpiece in a towel and gently pat dry
•  Gently detangle hair using Wide Tooth Comb
•  Spray with Leave-In Conditioning Spray (3-5 pumps) keeping away from base

•  Allow wig or hairpiece to air dry naturally by placing on a plastic or wire wig stand. Do NOT blow dry
•  Air drying your wig will give the best results. The fiber will dry fastest; be sure the cap is completely dry before wearing, storing, or displaying
•  Apply HD Smooth Detangling Spray, (3-5 pumps) focusing on the bottom half of wig or hairpiece. Gently comb through using your Wide Tooth Comb
•  Use ONLY the Jon Renau wide tooth comb is used on your HD fiber. Other tools will cause frizzing/tangling
•  HD fiber can withstand heat up to 350° F, however, Jon Renau recommends working at 270°-280° F
•  It is recommended to use professional grade heat styling tools with digital temperature settings to control heat

•  Heat your curling or flat iron to 270°-280° F
•  Using your Jon Renau Wide Tooth Comb, gently comb hair free of tangles
•  Starting at the nape, take ½ inch-1.5 inch sections of hair (smaller sections=tighter curls, larger sections=looser curls)
•  Spray Heat Treat Thermal Spray on the section to protect the fiber (1-2 pumps per section)

•  Gather hair into curling iron, smooth through to the ends. Roll iron up towards base of wig or hairpiece, staying 1-2 inches away
•  Hold for 10-15 seconds, then turn the tip of iron toward the ground and release curl into palm of hand
•  Holding curl in one hand, gather up towards base and secure curl with a small metal clip (like a pin curl)
•  Allow curl to cool completely (about 5 minutes); remove clip and let curl hang naturally

•  Starting at the nape, take ½ inch-1.5 inch sections
•  Spray Heat Treat Thermal Spray on the section to protect the fiber (1-2 pumps per section)
•  Slowly smooth flat iron down through ends; keep hair smooth by following behind the flat iron with your Wide Tooth Comb
•  Allow hair to hang naturally and cool completely

•  All synthetic fibers can tangle and frizz with wear. It is important that the frizz is corrected early to avoid permanent damage to the fiber. Use your flat iron to smooth any frizz before washing
•  We recommend using HD Smooth Detangling Spray with a Wide Tooth Comb DAILY to detangle your HD wig. This is especially important with the mid-length to long length HD wigs or hairpieces
•  To add texture and definition, use a small amount of Piece Out Contour Fiber Crème and apply using fingertips


Providing outstanding service, wigs and accessories to women suffering from hair loss. Helping women to look good and feel good.